Used Recipricating Gas High Pressure Compressors

Stock# 53752001

Used Neuman & Esser Reciprocating Gas Compressor, Type 3V1-370/260/120, Model V. 3 stage; 1 crank; 64.0 Nm^3 capacity; 0 bar g suction pressure; 42 bar g final pressure; 980 RPM compressor speed; 100mm stroke; 140kW BHP. Serial# 990 685 , Built 1999.

Stock# 53901001

Unused- PowerFuel Compressed Natural Gas (CNG) Fueling Station, BE-10 Series. 9 CFM/4.3 GGE/hr charge rate; 540 CFH/554,580 BTU/hr gas usage; 5000 psig max. discharge pressure; 1/5 psig min/max inlet pressure; 1350 RPM compressor RPM; (3) stage reciprocating system; (2) condensate drain valves; Automatic PLC controlled. Driven by a 3/230V, 5HP electric motor. OAD: 27.5" W x 41.3" H x 26.3" D.

Stock# 40181003

Unused- Hydro-Pac Inc. LX-Series Cylinder CO2 Inert Gas Compressor, Model CO2.6-15-400LX/CC-CO2-SYS-01; 2,575 psig maximum discharge pressure; 400 psig maximum pressure delta; Capacity at 2300 psig, 93 degrees C inlet and 2,500 psig discharge 2650 kg/h (868 scfm); 50-104 degrees F ambient operating temperature; 4 gpm at 60-80 degrees F cooling requirement; 15 hp, 3/60/575V; Serial # EP17-1080-1; New in 2017. CO2 must be dry, water moisture will cause corrosion. Still in original crate.

Stock# 14195009

Used PDC Model PDC-4-1250-6000 Hydrogen Gas Compressor. Maximum inlet pressure of 225 PSIG, a maximum inlet temperature of 120F, and a maximum discharge pressure of 6000 PSIG. The electric motor is rated at 30 horsepower, operates at 460 volts, 3 phase, 60 Hz, with a speed of 1750 RPM and a full load amperage of 36. It features a TEFC enclosure. Pneumatic drive specifications are not listed. The compressor skid dimensions are 65.00" in length, 47.00" in width, and 70.00" in height, with a total weight of 2500 lbs. It is a two-stage configuration. Flow specifications include an inlet pressure of 225 PSIG, inlet temperature of 75F, discharge pressure of 6000 PSIG, and a minimum flow of 35 SCFM. Contacting metals include 316 SS and 301 SS, with seals made of Viton and Vespel-SP1. The unit uses 1/2" Swagelok connections for both process inlet and outlet, 1/2" NPTF for coolant inlet and outlet, 1.00" NPTF for vents, and 1/4" NPTF for air connections.

Stock# 53566001

Used Hydro-Pac LX Carbon Dioxide Compressor, Model C02.2-60-1975LX-CO2. Single stage; 400 to 2176 psi suction pressure; 2176 psi max. discharge pressure; Capacity @ 600 psig, 55 degree F inlet: 127 scfm; Capacity @ 870 psig, 55 degree F inlet: 989 scfm; 15 gpm (minimum) cooling water requirements at 60-80 degrees F. 60 HP, 3/60/230/460V motor, 120V control. Built 2020.

Stock# 14195010

Unused- Skidded Co2 Recycle Compressor. Packaged by Toromont in 20062007 and stored by GE from 2007 to 2013, this unit was originally designed for recycle CO2 compression in a coal gasification project that was later canceled. It features an Ariel frame, model JGP 1 or 2, with a 3" stroke operating at 1800 RPM, driven by an 85 HP electric motor. The compressor includes a 4.75" cylinder, class JG, and is designed for a pressure of 865 psi. The systems piping, valves, fittings, and heat exchangers are primarily constructed from stainless steel and rated for 865 psi. It is currently configured as a single-cylinder compressor but is capable of being retrofitted for two-cylinder service.

Stock# 14195008

Used Gemini Gas Compressor, Model 125 HPSS, 4 Stage 300 CFM. CNG (Compressed Natural Gas) compressor system includes a four-stage, water-cooled, reciprocating compressor designed for efficient gas compression up to high pressures. U.S. Motors 125 HP, 1760 RPM, 460 Volt motor (S/N X783119) and includes an MK-AJ 24" recapture tank (S/N 9605). It is equipped with an EI C36-0527 cooler (S/N 93483) and a three-cylinder ASME cascade system, each cylinder measuring 20" x 11'6", rated for 5,000 psig and 5,711 cu. ft., with serial numbers 43338, 43339, and 43340. The unit utilizes a Marcum 11 Valve Electro-Pneumatic PMV/SMV priority/sequence panel for flow control. Compression is handled by a Quincy F340-80 air compressor rated at 7.5 HP, 460 Volt, with a discharge aftercooler (S/N 6019514). Drying is managed by a Wilkerson DE3 Twin Tower Heatless Dryer housed in a NEMA 4 enclosure (S/N 4339311). Fuel dispensing is facilitated by two DVCO 2020D dispensers with Hansen nozzles, serial numbers 930034 and 930037.and includes an air-cooled aftercooler, inter-stage separators, and safety relief valves on all stages. The compressor is skid-mounted with an integrated control panel for monitoring and automation, and it is designed for continuous-duty operation. Suitable for vehicle fueling stations or industrial applications, the unit ensures reliable performance with built-in protection systems.

Stock# 53393001

Used Siad Skid Mounted O2 / Oxygen Compressor, Type MS3/1602-B3H, Item# C40. Approximate 2,650 Nm3/h. 3-Stage compressor. Driven by a 450HP motor. Handled flow 75,000 Scfh. Suction pressure 0,4 psi g at 95 degrees F. Delivery conditions 175 psi g at 104 degrees F. Cooling inlet water temperature 85 degrees F, outlet water temperature 103 degrees F, required flow 103 GPM. Control Panel. Serial# K30514/10A, Built 2003.